The Chevron Latte Shirt, Part 1

The journey to the Pink Shirt (I haven’t forgotten about it) has so far spawned not one, but two side projects that have surprised me with the results.

The first was the Peppermint Stick Shirt, and the second is what I’m calling the Chevron Latte Shirt.

I’m presenting the Chevron Latte Shirt in three blog posts. Today’s is the first, covering the pattern work to address the fitting issues. The second will cover construction details, and the third will show the finished shirt. (Impatient readers can see work-in-progress photos on my Instagram feed).

Fitting, Again

When I finished the Peppermint Stick Shirt, I noticed the pattern still had some minor fitting issues.

  1. When fully buttoned, the front of the collar felt a little tight, as if it were cutting into me. (The back of the collar felt fine).
  2. The front band, right below the collar, buckled a bit between the collar and the first button when the collar was fully buttoned.
  3. With the collar unbuttoned, two drag lines ran from the shoulder tips to the second button of the shirt.
  4. The shirt felt a bit tight across the upper chest at shoulder level in front.

IMG_20160818_170340_result

I also found issues (1) and (2) were also present on the Blue Gingham Shirt, also made from this pattern. Issues (3) and (4) do appear on the Blue Gingham Shirt, but are not very noticeable.

I’m not sure why the Peppermint Stick Shirt has the issues with the tightness and the drag lines across the chest. It might be because it was cut on the cross grain to make the strips fall vertically, but I’m not sure. A pattern can fit differently when made with different fabrics. But with two shirts made on the same pattern, I could see there were still some minor fit issues, common to both, I wanted to fix.

Perfect Is The Enemy of Good

As an engineer, I constantly remind myself that “perfect is the enemy of good”, so I was reluctant to play around with the pattern more. Both the Blue Gingham Shirt and the Peppermint Stick Shirt fit me pretty well as-is. But I also thought that I could improve it, and since I have the pattern stored digitally on the computer, I could always go back to the previous pattern if I wasn’t successful.

I experimented a bit with pinning both shirts to test out some of my fit ideas.  I also made another muslin to test the changes before making the pattern alterations on the computer.

Here are the changes I made to the pattern:

  • a) Lower the neckline in front by about 1/4 inch, and blend it up into the neckline at the point the front piece meets the yoke. This should address Fit issue (1).
  • b) Make a slight adjustment for square shoulders. This should address fit issue (3). The alteration raises the shoulder tip by about 1/4 inch, making the shoulders less sloped.
  • c) Add 1/2 inch of ease across the front of the shirt. The added ease addresses issue (4) directly, and was determined by playing with the muslin.  I don’t really need the extra ease in the front below the chest, but I’m not going to care about an extra half inch.

Pattern Alterations

Here’s what the pattern alterations look like in Wild Ginger’s Pattern Master. The orange outlines show the previous pattern, the blue lines show the altered version. I’ve removed seam allowances for clarity.  (Click or tap for larger versions).

Yoke

The yoke piece shows the effects of the square shoulder adjustment. The new yoke has a less sloped shoulder.

snip_20160828172415

Shirt Front

The front piece shows several alterations made at once. The neckline is lowered, and the shoulders squared. This causes the armscye to raise up to meet the new shoulder tip. Finally, I added 1/4 inch to the center front, for 1/2 inch of extra ease total.  (The dashed line is center front).

snip_20160828172409

Sleeve

Finally, the sleeves are lengthened by 1/4 inch to accommodate the armscye rising 1/4 inch.

snip_20160828172344

The collar and stand pieces also get a little bit longer, because the neckline increases in circumference a small amount. I haven’t shown that alteration here.

Next Time

After updating the pattern, I wanted to see an actual shirt made from it before committing to making the Pink Shirt.  So I’ll talk about constructing the Chevron Latte Shirt.

2 thoughts on “The Chevron Latte Shirt, Part 1

    1. mportuesisf Post author

      Thank you! I was really happy with the way that project came together. The buttons were a big part of it.

Comments are closed.